Research with a bite

The bite curves of a praying mantis - measured by the forceX system can be seen

The bite curves of a praying mantis - measured by the forceX system can be seen on the laptop. In the background, Peter T. Rühr is performing the measurement. © Photo: Volker Lannert/University of Bonn

Scientists at the University of Bonn present a sensor system that can measure the bite force of insects

How hard can insects bite? Having a strong chewing apparatus makes it easier to crush harder food and to succeed in fights with enemies. Biologists at the University of Bonn now present a mobile system (forceX) for measuring the bite forces of small animals, along with the software forceR to evaluate the data. This allows to understand how bite forces, for example of insects, evolved. The final version is now published in the journal "Methods in Ecology and Evolution".

The praying mantis wriggles a little in the scientist’s hand. When the insect approaches the sensor, it defends itself by biting down on the two metal plates that transfer the pressure to a piezo crystal. The crystal generates a load-dependent voltage that is transmitted to a laptop via an amplifier. Curves appear on the screen, some of which rise steeply and shakily reach a plateau before dropping back to zero. Sometimes the ascent and descent are flatter - depending on how fast the particular insect approaches maximum force when biting.

Hardly any data on bite force "There is hardly any data available on how hard insects can bite," says Peter T. Rühr, a doctoral candidate at the Institute of Evolutionary Biology and Ecology at the University of Bonn. With their sensor system "forceX", the researchers want to investigate how the mandibles, musculature and head shape of insects have evolved to meet the challenges of their respective environments. "It may not always be advantageous to be able to bite hard, because maintaining the ability to bite strong demands higher energetic costs," Rühr says. The bite force may depend, for example, on what food an insect feeds on or whether it needs the mandibles to defend itself.


The team led by Alexander Blanke, who has secured a Starting Grant from the European Research Council (ERC), further developed existing systems for measuring bite forces.

In the measurement setup of the researchers at the University of Bonn, a stereo microscope, akin to a strong magnifying glass, is used to detect whether the mandibles of the investigated insect are in contact with the metal plates of the sensor at the correct location. The lower plate is immobile, while the upper one transmits the force to the sensor via a rocker.

Flexible adjustment to mandible size possible "Depending on the size and opening angle of the mandibles, we use differently sized, interchangeable bite plates," says Rühr, explaining the advancements. "This allows the sensor to be adjusted over a relatively wide range to meet the particular requirements of the animals." The complete system is battery-powered and can therefore be used for mobile measurements - even in the "wild".

For stinging insects, the researchers use a holder made of plastic. The animals disappear completely in the vial, with only the head with its mouthparts protrudes from a small hole in the front. Rühr: "This allows us to better position the insects without having to hold them in our hands." Usually, the animals do not need much persuasion before they bite. They feel uncomfortable in the unfamiliar environment and fight back with defensive bites. If this instinctive behavior fails to materialize, the researchers stroke the insect heads with a delicate brush - at the latest then the insects will close their jaws.

High accuracy of the measurement


For publication in Methods in Ecology and Evolution, the researchers determined the accuracy of the system: They did this by attaching different weights, ranging from one gram to almost one kilogram, to the movable metal plate. A total of 1,600 repetitions show that the deviation between measurements is a maximum of 2.2 percent. "That is very accurate," says Rühr. The system can also be used to measure the force of scorpion or crab claws, for example.

Rühr and Blanke built the system during their time at the University of Cologne, in part with the local precision engineering workshop. At the University of Bonn, they further optimized it and performed the accuracy measurements. The manuscript also describes the the new "forceR" software, with which the bite force values and shapes of the bite curves can be evaluated and compared. The researchers do not want to bring the bite force sensor system to market. "Rather, the results presented in ’Methods in Ecology and Evolution’ provide the basis for replicates," Rühr says. Essential parts of the sensor can even be reproduced using a 3D printer.


Participating institutions and funding:

Beyond the University of Bonn, the University of Cologne was also involved. Funding is provided by the European Research Council (ERC) and the German Research Foundation (DFG).


Publication: Peter T. Rühr, Alexander Blanke: forceX and forceR: a mobile setup and R package to measure and analyse a wide range of animal closing forces, "Methods in Ecology and Evolution", DOI: 10.1111/2041-210X.13909; URL: https://besjournals.onlinelibrary.wiley.com/doi/abs/10.1111/2041-210X.13909

Recommended Links

This site uses cookies and analysis tools to improve the usability of the site. More information. |